dimensions are in inches, m illimeters are in parenthesis. ordering/part number information 719p 222 5 1500 m b 3 C xxx a suffix may be added to denote special construction, marking, packaging, test requirements, etc. lead length 1 = 0.187 (4.7) 0.030 (0.8) 2 = 0.250 (6.4) 0.030 (0.8) 3 = 1.250 (32) minimum other specific lead lengths available upon request lead style a = straight lead b = hairpin crimp d = hockey stick crimp case code set code for factory reference. ac voltage rating capacitance tolerance 9 = 10%; 5 = 5%; 3 = 3%; 2 = 2%; 1 = 1% capacitance expressed in picofarads. the first two digits are the significant figures, the third is the number of zeros following (i.e. 222 = 2200 pf = 0.0022 f) cde type number identifies basic capacitor design. 71 8p = round profile 719p = pressed p rofile standard marking format sample marking on unit cde719p1500vac 222j 0515 description cde - cde identification 719p - type number 1500vac - ac voltage rating 222j - capacitance and tolerance code 0515 - weekly date code (i.e. 15th week of 2005) tolerance codes per eia standards f 1% g 2% h 3% j 5% k 10% cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop?, high voltage polypropylene film/foil
application notes & considerations corona: corona is a small but locally intense electrical discharge that inje cts charge into the insulating film adjacent to edges of foil/metallization or a location where air is trapped between foil/metallization and the film. the discharge is caused by a voltage gradie nt large enough to ionize molecules in either the film or small air pockets. each discharge does some small but cumulative damage to the film. corona is a very important consideration for ac and/or pulse applications where the cumlative damage can rapidly accrue and cause dielectric failure. for a plain film & foil part this will result in a short circuit. however, for a capacitor employing metallized film the clearing around th e dielectric failure site results in progressive capacitance loss. the 718 p/719p series utilizes a hybrid film/foil design approach, incorporating the use of extended foil for direct connection of the lead wires and a floating metallized common. corona inception voltage (civ) is the peak-to-peak voltage at w hich corona discharge begins; it is also commonly referred to as corona start voltage (csv). it is traditionally expressed as the rms value of a sin e wave with the above peak-to-peak val u e. it is not practical to try and list all the facts a n d i s s u e s a s s o c i a t e d w i t h c o r o n a , t h e r e f o r e w e h i g h l y e n c o u r a g e y o u t o c o n t a c t u s t o d i s c u s s y o u r application and the importance of careful ly considering the effects of corona. dv/dt (pulse rise time) : pulse rise time, commonly referred to as dv/dt, is the maximum guaranteed repetitive rate of voltage change [ slew rate ] a capacitor can withstand without dam age during the lifetime of an application, expressed in volts/ sec or kv/ sec. dv/dt also expresses current pulse capability without requiring a nearly impossible pulse current measurement. pulse current is only an issue for a pure metallized capacitor where pulse currents above the rated value can destroy the connection to the metallization. with leads welded directly to extended foil, film /foil capacitor dv/dt is only limited by corona inception [ ac voltage rating ] and application circuit inductance. cdes dv/dt ratings are provided to assure capacitors are never operated in corona to assure highest possible reliability in pulse applications. as mentioned above we strongly encourage you to contact us with your questions and/or specific requirements. cde?s design philosophy: the cde approach is to design and manufacture capacitors to outlast the life of the product they are installed in. our units are designed and rated to ope rate continuously at the maximum limits stated in our specifications. there are times when an application will push these limits. our expertise lies in understanding the limits of film capacitors and we welcome the opportunity to assist you in understanding these limits also! cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop?, high voltage polypropylene film/foil
0.25? (6.4) max 1.083 (27.5) 0.020 (0.5) l max lead style a 0.060? (1.5) max lead length 1.407 (35.7) 0.030 (0.8) lead length l max 1.344 (34.1) 0.020 (0.5) l max lead length 0.25? (6.4) max d di a max lead style d lead style b dimensions are in inches, m illimeters are in parenthesis. lead styles/lead spacings cap max dv/dt peak i max % d.f. max esr (m ) value (f) part number* l max dia max wire (d ) (volts/sec) amps 10khz 100khz 10khz 100khz .00056 718p56151500m 1.60 (40.6) 0.30 (7.6 ) 0.032 (0.8) 357000 200 0.021 0.029 6106 812 .00068 718p68151500m 1.60 (40.6) 0.31 (7.9 ) 0.032 (0.8) 324000 220 0.021 0.029 5028 669 .00082 718p82151500m 1.60 (40.6) 0.33 (8.4 ) 0.032 (0.8) 295000 242 0.021 0.029 4170 555 .001 718p10251500m 1.60 (40.6) 0.35 (8.9 ) 0.032 (0.8) 267000 266 0.021 0.029 3419 455 .0012 718p12251500m 1.60 (40.6) 0.36 (9.1 ) 0.032 (0.8) 244000 292 0.021 0.029 2850 380 .0015 718p15251500m 1.60 (40.6) 0.39 (9.9 ) 0.032 (0.8) 218000 326 0.021 0.029 2280 304 .0016 718p16251500m 1.60 (40.6) 0.39 (9.9 ) 0.032 (0.8) 211000 338 0.021 0.029 2137 285 .0018 718p18251500m 1.60 (40.6) 0.41 (10. 4) 0.032 (0.8) 199000 358 0.021 0.029 1900 254 .0020 718P20251500M 1.60 (40.6) 0.42 (10. 7) 0.032 (0.8) 189000 378 0.021 0.029 1710 228 .0022 718p22251500m 1.60 (40.6) 0.44 (11. 2) 0.032 (0.8) 180000 396 0.021 0.029 1555 208 .0023 718p23251500m 1.60 (40.6) 0.44 (11. 2) 0.032 (0.8) 176000 404 0.021 0.029 1487 199 .0024 718p24251500m 1.60 (40.6) 0.45 (11. 4) 0.032 (0.8) 172000 414 0.021 0.029 1425 190 .0025 718p25251500m 1.60 (40.6) 0.46 (11. 7) 0.032 (0.8) 169000 422 0.021 0.029 1368 183 .0027 718p27251500m 1.60 (40.6) 0.47 (11. 9) 0.032 (0.8) 162000 438 0.021 0.029 1267 169 .0028 718p28251500m 1.60 (40.6) 0.48 (12. 2) 0.032 (0.8) 159000 446 0.021 0.029 1222 163 .0030 718p30251500m 1.60 (40.6) 0.49 (12. 4) 0.032 (0.8) 154000 462 0.021 0.029 1140 153 .0033 718p33251500m 1.60 (40.6) 0.50 (12. 7) 0.032 (0.8) 147000 484 0.021 0.029 1037 139 .0036 718p36251500m 1.60 (40.6) 0.52 (13. 2) 0.032 (0.8) 141000 506 0.021 0.029 950 127 .0039 718p39251500m 1.60 (40.6) 0.54 (13. 7) 0.032 (0.8) 135000 528 0.021 0.029 877 118 .0040 718p40251500m 1.60 (40.6) 0.54 (13. 7) 0.032 (0.8) 133000 534 0.021 0.029 855 115 .0043 718p43251500m 1.60 (40.6) 0.56 (14. 2) 0.032 (0.8) 129000 554 0.021 0.029 796 107 .0047 718p47251500m 1.60 (40.6) 0.58 (14. 7) 0.040 (1.0) 123000 578 0.021 0.029 728 97 .0050 718p50251500m 1.60 (40.6) 0.59 (15. 0) 0.040 (1.0) 119000 596 0.021 0.029 684 92 .0051 718p51251500m 1.60 (40.6) 0.60 (15. 2) 0.040 (1.0) 118000 602 0.021 0.029 671 90 .0056 718p56251500m 1.60 (40.6) 0.62 (15. 7) 0.040 (1.0) 113000 632 0.021 0.029 611 82 .0060 718p60251500m 1.60 (40.6) 0.63 (16. 0) 0.040 (1.0) 109000 654 0.021 0.029 570 77 .0062 718p62251500m 1.60 (40.6) 0.64 (16. 3) 0.040 (1.0) 107000 664 0.021 0.029 552 74 .0068 718p68251500m 1.60 (40.6) 0.67 (17. 0) 0.040 (1.0) 102000 696 0.021 0.029 503 68 .0070 718p70251500m 1.60 (40.6) 0.68 (17. 3) 0.040 (1.0) 101000 706 0.021 0.029 489 66 .0075 718p75251500m 1.60 (40.6) 0.70 (17. 8) 0.040 (1.0) 97000 730 0.021 0.029 456 61 .0080 718p80251500m 1.60 (40.6) 0.71 (18. 0) 0.040 (1.0) 94000 754 0.021 0.029 428 58 .0082 718p82251500m 1.60 (40.6) 0.72 (18. 3) 0.040 (1.0) 93000 764 0.021 0.029 417 56 .0090 718p90251500m 1.60 (40.6) 0.75 (19. 1) 0.040 (1.0) 89000 800 0.021 0.029 380 51 .0091 718p91251500m 1.60 (40.6) 0.75 (19. 1) 0.040 (1.0) 88000 806 0.021 0.029 376 51 .0093 718p93251500m 1.60 (40.6) 0.76 (19. 3) 0.040 (1.0) 88000 806 0.021 0.029 368 50 .01 718p10351500m 1.60 (40.6) 0.78 (19.8) 0.040 (1.0) 84000 844 0.022 0.029 342 46 .012 718p12351500m 1.60 (40.6) 0.85 (21. 6) 0.040 (1.0) 77000 924 0.022 0.029 285 39 type 718p, 1500 vac/5000 vdc sizes/ratings * for complete part number please refer to ordering/part number information page. cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop?, high voltage polypropylene film/foil
0.25? (6.4) max 1.083 (27.5) 0.020 (0.5) l max lead style a 0.060? (1.5) max lead length 1.407 (35.7) 0.030 (0.8) lead length l max 1.344 (34.0) 0.020 (0.5) l max lead length 0.25? (6.4) max h max d t max lead style d lead style b dimensions are in inches, m illimeters are in parenthesis. lead styles/lead spacings cap max dv/dt peak i max % d.f. max esr (m ) value (f) part number* l max t max h max wire (d) (volts/sec) amps 10khz 100kh z 10khz 100khz .001 719p10251500m 1.60 (40.6) 0.22 (5.6) 0.42 (10.7) 0.032 (0.8) 267000 266 0.021 0.029 3419 455 .0011 719p11251500m 1.60 (40.6) 0.23 (5.8) 0.43 (10.9) 0.032 (0.8) 254000 280 0.021 0.029 3109 414 .0012 719p12251500m 1.60 (40.6) 0.24 (6.1) 0.43 (10.9) 0.032 (0.8) 244000 292 0.021 0.029 2850 380 .0015 719p15251500m 1.60 (40.6) 0.26 (6.6) 0.46 (11.7) 0.032 (0.8) 218000 326 0.021 0.029 2280 304 .0016 719p16251500m 1.60 (40.6) 0.27 (6.9) 0.47 (11.9) 0.032 (0.8) 211000 338 0.021 0.029 2137 285 .0018 719p18251500m 1.60 (40.6) 0.29 (7.4) 0.48 (12.2) 0.032 (0.8) 199000 358 0.021 0.029 1900 254 .0020 719p20251500m 1.60 (40.6) 0.30 (7.6) 0.50 (12.7) 0.032 (0.8) 189000 378 0.021 0.029 1710 228 .0022 719p22251500m 1.60 (40.6) 0.31 (7.9) 0.51 (13.0) 0.032 (0.8) 180000 396 0.021 0.029 1555 208 .0023 719p23251500m 1.60 (40.6) 0.32 (8.1) 0.52 (13.2) 0.032 (0.8) 176000 404 0.021 0.029 1487 199 .0024 719p24251500m 1.60 (40.6) 0.33 (8.4) 0.52 (13.2) 0.032 (0.8) 172000 414 0.021 0.029 1425 190 .0025 719p25251500m 1.60 (40.6) 0.33 (8.4) 0.53 (13.5) 0.032 (0.8) 169000 422 0.021 0.029 1368 183 .0027 719p27251500m 1.60 (40.6) 0.35 (8.9) 0.54 (13.7) 0.032 (0.8) 162000 438 0.021 0.029 1267 169 .0028 719p28251500m 1.60 (40.6) 0.35 (8.9) 0.55 (14.0) 0.032 (0.8) 159000 446 0.021 0.029 1222 163 .0030 719p30251500m 1.60 (40.6) 0.36 (9.1) 0.56 (14.2) 0.032 (0.8) 154000 462 0.021 0.029 1140 154 .0033 719p33251500m 1.60 (40.6) 0.38 (9.7) 0.58 (14.7) 0.032 (0.8) 147000 484 0.021 0.029 1037 139 .0036 719p36251500m 1.60 (40.6) 0.40 (10.2) 0.59 (15.0) 0.032 (0.8) 141000 506 0.021 0.029 950 127 .0039 719p39251500m 1.60 (40.6) 0.41 (10.4) 0.61 (15.5) 0.032 (0.8) 135000 528 0.021 0.029 877 118 .0040 719p40251500m 1.60 (40.6) 0.42 (10.7) 0.61 (15.5) 0.032 (0.8) 133000 534 0.021 0.029 855 115 .0043 719p43251500m 1.60 (40.6) 0.43 (10.9) 0.63 (16.0) 0.032 (0.8) 129000 554 0.021 0.029 796 107 .0047 719p47251500m 1.60 (40.6) 0.43 (10.9) 0.67 (17.0) 0.040 (1.0) 123000 578 0.021 0.029 728 97 .0050 719p50251500m 1.60 (40.6) 0.44 (11.2) 0.69 (17.5) 0.040 (1.0) 119000 596 0.021 0.029 684 92 .0051 719p51251500m 1.60 (40.6) 0.45 (11.4) 0.69 (17.5) 0.040 (1.0) 118000 602 0.021 0.029 671 90 .0056 719p56251500m 1.60 (40.6) 0.47 (11.9) 0.71 (18.0) 0.040 (1.0) 113000 632 0.021 0.029 611 82 .0060 719p60251500m 1.60 (40.6) 0.49 (12.4) 0.73 (18.5) 0.040 (1.0) 109000 654 0.021 0.029 570 77 .0062 719p62251500m 1.60 (40.6) 0.49 (12.4) 0.74 (18.8) 0.040 (1.0) 107000 664 0.021 0.029 552 74 .0068 719p68251500m 1.60 (40.6) 0.52 (13.2) 0.76 (19.3) 0.040 (1.0) 102000 696 0.021 0.029 503 68 .0070 719p70251500m 1.60 (40.6) 0.53 (13.5) 0.77 (19.6) 0.040 (1.0) 101000 706 0.021 0.029 489 66 .0075 719p75251500m 1.60 (40.6) 0.54 (13.7) 0.79 (20.1) 0.040 (1.0) 97000 730 0.021 0.029 456 61 .0080 719p80251500m 1.60 (40.6) 0.56 (14.2) 0.81 (20.6) 0.040 (1.0) 94000 754 0.021 0.029 428 58 .0082 719p82251500m 1.60 (40.6) 0.57 (14.5) 0.82 (20.8) 0.040 (1.0) 93000 764 0.021 0.029 417 56 .0090 719p90251500m 1.60 (40.6) 0.60 (15.2) 0.84 (21.3) 0.040 (1.0) 89000 800 0.021 0.029 380 51 .0091 719p91251500m 1.60 (40.6) 0.60 (15.2) 0.85 (21.6) 0.040 (1.0) 88000 806 0.021 0.029 376 51 .0093 719p93251500m 1.60 (40.6) 0.61 (15.5) 0.85 (21.6) 0.040 (1.0) 88000 806 0.021 0.029 368 50 .01 719p10351500m 1.60 (40.6) 0.63 (16.0) 0.88 (22.4) 0.040 (1.0) 84000 844 0.022 0.029 342 46 .012 719p12351500m 1.60 (40.6) 0.70 (17.8) 0.94 (23.9) 0.040 (1.0) 77000 924 0.022 0.029 285 39 type 719p, 1500 vac/5000 vdc sizes/ratings * for complete part number please refer to ordering/part number information page. cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop?, high voltage polypropylene film/foil
1500 100 1000 10000 voltage (rms) 10 100 1000 frequency (khz) 0.00056 0.001 0.0022 0.0047 0.012 1500 100 1000 10000 voltage (rms) 10 100 1000 frequency (khz) 0.00056 0.001 0.0022 0.0047 0.012 1500 100 1000 10000 voltage (rms) 10 100 1000 frequency (khz) 0.00056 0.001 0.0022 0.0047 0.012 t yp e 718p rms volta g e vs. fre q uenc y at 70 c ambient t yp e 718p rms volta g e vs. fre q uenc y at 85 c ambient t yp e 718p rms volta g e vs. fre q uenc y at 95 c ambient please refer to page 8 for important information regarding these performance curves cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop, high voltage, polypropylene film/foil
1500 100 1000 10000 voltage (rms) 10 100 1000 frequency (khz) 0.001 0.0018 0.0033 0.0068 0.012 1500 100 1000 10000 voltage (rms) 10 100 1000 frequency (khz) 0.001 0.0018 0.0033 0.0068 0.012 1500 100 1000 10000 voltage (rms) 10 100 1000 frequency (khz) 0.001 0.0018 0.0033 0.0068 0.012 t yp e 719p rms volta g e vs. fre q uenc y at 70 c ambient t yp e 719p rms volta g e vs. fre q uenc y at 85 c ambient t yp e 719p rms volta g e vs. fre q uenc y at 95 c ambient please refer to page 8 for important information regarding these performance curves cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop?, high voltage polypropylene film/foil
rms voltage vs. frequency performance curve data and thermal considerations with todays demanding and complex applications it is more critical than ever t o have a co mprehensive understanding of therm al issues. b ecause thermal environments vary co nsiderably, our app roach is to provide rms voltage versus freque ncy performance curves based on th e following parameters to be utilized as a guideline in specifying the appropriate part: ? +70 c, +85 c, and +95 c ambient temperatures ? pure convection cooling ? all heat dissipation from the lead wire is added to the capacitor ? increased lead wire dissipation at high frequencies is included [skin effect losses] the ambient temperature is the air temperature adjace nt to the capacitor within the application enclosure at the highest exterior temperature permitted by the end user. since the maximum allowable temperature for polypropylene is +1 05 c, our performance cur ves are base d on a pow er level that raises t he temperature +20 c from ambient to the hot spot within the capacitor. we realize that the environment assu med by our pe rformance curves is highly un likely to represent that of a real application. we also un derstand that a "pure co nvection" environment is also highl y improbable. there will almost always be a circuit board and other adjacent components that will impede convection based air circulation, and the capac itor under dis cussion will not be the only heat generating device present! beca use of all this " variability" our performance curves are cal culated conservatively. considerations: the application power level can be compared to the performance curves at a given frequency by the following calculation: (actual vac/rated vac) 2 = power level relative to performance curve power temperature rise is directly related to power; power is related to the voltage squared. since the maximum allowable temper ature for pol ypropylene is +105 c we strongl y recommend that you check t he case temperature of the capacitor un der worst case conditions . the capacitor surface temperature should be less than: capacitor surface temperature < 0.67 * (105 C t ambient) + t ambient please contact us for more detailed information a nd methods to optimize allowable voltage in your electrical/thermal environment. we always welcome an engineer-to-engineer discussion of your particular situation! cde cornell dubilier ? 1605 e. rodney french blvd. ? new bedford, ma 02744 ? phone: (508)996-8561 ? fax: (508)996-3830 type 718p/719p, orange drop?, high voltage polypropylene film/foil
4 notice and disclaimer: all product drawings, descriptions, specifcations, statements, information and data (collectively, the information) in this datasheet or other publication are subject to change. the customer is responsible for checking, confrming and verifying the extent to which the information con - tained in this datasheet or other publication is applicable to an order at the time the order is placed. all information given herein is believed to be accurate and reliable, but it is presented without any guaran - tee, warranty, representation or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on the knowledge that the cornell dubilier company providing such statements (cornell dubilier) has of operating conditions that such cornell dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representa - tion regarding any such matter C and cornell dubilier specifcally and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specifc customer application, use, storage, transportation, or operating environment. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by cornell dubilier with reference to the use of any cornell dubilier products is given gratis (unless otherwise specifed by cornell dubilier), and cornell dubilier assumes no obligation or liability for the advice given or results obtained. although cornell dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indi - cated in such warnings, cautions and notes, or that other safety measures may not be required. ac
|
